 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 10 Base-T Card Bus Module with Integrated Predistortion Resistors ELECTRONICS INC. EPE6138A * For Card Bus ASIC solutions requiring predistortion * (similar to AT&T T7240) * Robust design allows for toughest soldering processes * * Complies with or exceeds IEEE 802.3, 10 Base-T Requirements * Electrical Parameters @ 25 C Cut-off Frequency (MHz) 1.0 MHz Xmit 17 Rcv 17 Insertion Loss * (dB Max.) 1-10 MHz Xmit -1 Rcv -1 Return Loss (dB Min.) 5-10 MHz Xmit -18 Rcv -18 @ 20 MHz Xmit -7 Rcv -5 Attenuation (dB Min.) @ 25 MHz Xmit -18 Rcv -11 @ 30 MHz Xmit -35 Rcv -18 @ 40 MHz Xmit -35 Rcv -18 @ 50 MHz Xmit -45 Rcv -40 Common Mode Rejection (dB Min.) @ 100 MHz Xmit -35 Rcv -30 @ 200 MHz Xmit -30 Rcv -25 Crosstalk (dB Min.) @ 1-10 MHz Xmit -50 Rcv -50 * * Isolation : meets or exceeds 802.3 IEEE Requirements * Characteristic Filter Impedance : 100 ohms * *Excluding resistor networks Transmit Channel 68.1 Schematic 3 8 49.9 Receive Channel 12 13 LPF 100 7 287 6 LPF 100 2 49.9 5 4 68.1 1:1 9 10 Media Side 1:1 14 287 Chip Side 1 Chip Side Media Side Package A J Pin 1 I.D. PCA EPE6138A Date Code Dim. Min. .780 .510 .074 .600 .003 .100 .650 .016 .010 .100 0 .030 Dimensions (Inches) Max. Nom. .800 .530 .084 Typ. .010 Typ. .670 .020 Typ. Typ. 8 .050 .030 .200 .085 .700 (Millimeters) Min. Max. Nom. 19.81 12.95 1.88 15.24 .076 2.54 16.51 .406 .254 2.54 0 .762 20.32 13.46 2.13 Typ. .254 Typ. 17.02 .508 Typ. Typ. 8 1.27 .762 5.08 2.16 17.78 N B Q Pad Layout P D E C M K L I A B C D E F G H I J K L M N P Q H F G PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CSE6138Aa Rev. B 1/7/97 Product performance is limited to specified parameters. Data is subject to change without prior notice. TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com 10 Base-T Card Bus Module with Integrated Predistortion Resistors ELECTRONICS INC. EPE6138A The circuit below is a guideline for interconnecting PCA's EPE6138A with ASICS for 10 Base-T PHY chip over UTP cable. Further details of system design, such as chip pin-out, etc. can be obtained from the Card Bus specific chip manufacturer. Typical insertion loss of the isolation transformer/filter is 0.7dB. This parameter covers the entire spectrum of the encoded signals in 10 Base-T protocols. However, the predistortion resistor network introduces some loss which has to be taken into account in determining how well your design meets the Standard Template requirements. Thevenin's equivalent termination impedance provided by the transmitt outputs is 2*(287//68.1) ohms or approx. 110 ohms. Thus, bench testing for return loss will assume an output impedance less than 1 ohms on each of the driver outpust. Note that some systems have auto polarity detection and some do not. If not, be certain to follow the proper polarity. It is recommended that system designers ground the chip side center taps via a low voltage capacitor. Taking the cable side center taps to chassis via capacitors, is not recommended, as this will add cost without containing EMI. This may worsen EMI, specifically if the primary "common mode termination" is pulled to ground as shown. The pulldown resistors used around the RJ45 connector have been known to suppress unwanted radiation that unused wires pick up from the immediate environment. Their placement and use are to be considered carefully before a design is finalized. It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit the plane off at least 0.08 inches away from the chip side pins of EPE6138A. There need not be any ground plane beyond this point. For best results, PCB designer should design the outgoing traces preferably to be 50 ohms, balanced and well coupled to achieve minimum radiation from these traces. Typical Application Circuit for UTP PC Card TX+ TXd+ 7 6 10 8 9 14 1 TX 2 3 RX 6 4 5 7 8 RJ45 TXASIC CARD BUS TXdPHY RX+ 5 4 EPE6138A 1 12 2 3 13 RXChassis Ground PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CSE6138Ab Rev. B 1/7/97 TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com |
Price & Availability of EPE6138A
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |